PCB Assembly and REV-B of the board

viernes, 5 de mayo de 2017 0 Comentarios, Dejar un Comentario

The PCBs finally arrive, and it is time to test if anything went wrong, or if we need to make the Rev-B of the board, It almost works as spect it but i decided to make some changes in the board to increase the specs. This the board with all the components on their respective places.


REV-A Front face


REV-B Back Face


The new specs will be that we can light the PBBW in more tones that just the Red, Green and Blue LEDs one at a time as I put a single resistor in the common anode of the RGB LED, in that configuration just one color of each RGB LED can be turn on at the same time, but if we add a resistor for each LED we could make some color combinations, like a nice rainbow contained in our device. I have also change the form factor of the Buzzer, now it will be a SMT.

So let me show you how the new schematic looks like:


SCHEMATICS REVB

And a 3D look of the board before send it to fabrication:


So now we are ready to send the GERBER Files for fabrication, and in a week from now you will see working.


OCDC - Electronic Design

martes, 2 de mayo de 2017 0 Comentarios, Dejar un Comentario
So the electronic part of the project its going to be very simple, but a good look.
This circuit would drive the heater element by reading a temperature sensor and adjusting the heater activation accordingly, but the special effects, the visual and good look of this will be 8 RGB LEDs with a shape of a ring like in the image of the concept design idea, this board should also be capable of charging the battery and respond to a human interface, in this case 3 push-buttons.

This is the schematic i made for this task.
Portable Baby Bottle Warmer - Schematic REV-A

In order for this board to look nice i made it round, and its time to get it manufacture. 


PCB - REV A

And this is the 3D model of it:


PCB - Front View


PCB - Back View


PBBW Assembly View


PBBW Explode View

 I have already think of some improvement I can make to the project, so this will not be the final version. Wait for more...


3D Concept Idea of the Portable baby bottle warmer

jueves, 6 de abril de 2017 0 Comentarios, Dejar un Comentario
In order to the electronics to take place in the design of the project its necessary to know how it would the product would behave, the interface to the user and the aspect of it ( Dimensions). That is why i decided to make some 3D drawings of how i imagine the product would look like in real life and try to make it according the specifications i talked about in the first post of this project.

So this is how i would like it look like:
In order to this concept idea to work i have drawn the following functional parts that you can see in the following exploded view.
The white pieces will be ABS plastic and the red one will be a translucent acrylic plastic for the Wurth RGB LEDs as an interface (visual interface) with the user, representing by its color the current, target temperature and notifications, the electronics and battery should be contained in the bottom part of this baby bottle warmer.

As a heating element i would like to use a Thermoelectric cell, in the bottom side will cool the MOSFET that will drive it and in the top side it will warm the baby feeding bottle, in this way i will not need a special heatsink for the MOSFET to cool it down.

So this are some of the part that will make posible this idea:

In the next post we will start by designing the electronics that will fit the bottom part of this design and the Wuth's Wireless Power Module.




Connecting a different load to the Wireless Power Kit

martes, 28 de marzo de 2017 0 Comentarios, Dejar un Comentario
Connecting another load to the Wireless Power Kit its pretty straight forward, as simple as to solder two cables. In this case I tried another LED module, but this with higher power specifications.

 In order to connect this load first of all we need to find the following pads labeled VOUT and GND, this pads and pins are capable of provide 10v @1A - in other words 10W output power.

Connecting another load

This way we have the specified power output described above, now lets mesure the Voltage and Current:

Voltage reading of 10.02 volts of 10 volts specified. 

Current capabilities of 1.1 Amps (10W)

So this kit by it self its capable of recharging a two cell battery without a problem and very fast also.
We could charge a two cell battery of 1000mAh rated 1C for charge within just 1 hour, that sounds good enough for our application.

Now that we now the power output capabilities we can select our battery and battery charger for our Feeding Baby Bottle Warmer. In the next post i will show what I will use as a heater element that will be in charge of getting the baby bottle at the right temperature.

If you have any comment or questions please leave them in the comment section below.